Nope.
The engine pods were an exercise in CAD and balsa sheeting.
They are fiberglass now.
Scot
The engine pods were an exercise in CAD and balsa sheeting.
They are fiberglass now.
Scot
- Welcome to Battlezone Universe.
News:
Welcome to the BZU Archive dated December 24, 2009. Topics and posts are in read-only mode. Those with accounts will be able to login and browse anything the account had access granted to at the time. No changes to permissions will be made to be given access to particular content. If you have any questions, please reach out to squirrelof09/Rapazzini.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#1
Overdrive Terminal / Re: How to motivate Activision to make Battlezone 3
December 22, 2009, 03:56:00 PM #2
Maps and Modding / Re: Converting Battlezone II Maps for use in the Valve Hammer Editor
December 20, 2009, 05:52:27 PM
I'd love to know what map this will be in the Half-Life 2 servers.
Scot
Scot
#3
Overdrive Terminal / How to motivate Activision to make Battlezone 3
December 20, 2009, 05:32:44 PM
I posted this on the Battlezone Club Forum and FirBirGir said should post it here.
I know I haven't posted much but getting the e-mail about the latest BZ Enhanced download made me get my copy of Battlezone out and start playing it again.
I still am amazed at the quality in game play and graphics.
I started thinking what could possibly coax Activision to create Battlezone 3.
I have seen polls on the internet but they don't sem to get much attention from Activision.
What if fans pulled their collective tallents, generated blueprints and built a couple full scale grizzly tanks, scouts or scavengers and brought them to a future E3 Convention.
I know this sounds like an epic task to take on but it can be done.
I was a part of a group of Star Wars fans that wanted to build a accurate replica of the Landspeeder from A New Hope and it finally was finished.
A scout would be small and easy to build, the grizzly would be larger but possible to build in a 2 car garage, the scavenger may be a bit too big.
Because they are all facetted it would be easy to build a plywood on frame mock-up, seal it with plaster, paint and weather.
What I need to know is if there is any way to pull the wire frame vehicles off Battlezone and convert them into a dfx or dwg format.
If that can be done then the rest would be easy.
Let me know what you guys think.
Scot
I know I haven't posted much but getting the e-mail about the latest BZ Enhanced download made me get my copy of Battlezone out and start playing it again.
I still am amazed at the quality in game play and graphics.
I started thinking what could possibly coax Activision to create Battlezone 3.
I have seen polls on the internet but they don't sem to get much attention from Activision.
What if fans pulled their collective tallents, generated blueprints and built a couple full scale grizzly tanks, scouts or scavengers and brought them to a future E3 Convention.
I know this sounds like an epic task to take on but it can be done.
I was a part of a group of Star Wars fans that wanted to build a accurate replica of the Landspeeder from A New Hope and it finally was finished.
A scout would be small and easy to build, the grizzly would be larger but possible to build in a 2 car garage, the scavenger may be a bit too big.
Because they are all facetted it would be easy to build a plywood on frame mock-up, seal it with plaster, paint and weather.
What I need to know is if there is any way to pull the wire frame vehicles off Battlezone and convert them into a dfx or dwg format.
If that can be done then the rest would be easy.
Let me know what you guys think.
Scot
Pages1